No. 1 Fresher Jobs Website in India.
Are you employer? Register to Post Jobs Login
Search Jobs

ELXSI Paper Technical - Electronics by Tata

Details of ELXSI Paper Technical - Electronics by Tata conducted by Tata for job interview.
Share Us With Others

TATA ELXSI PAPERS HELD AT DRIEMS ,CUTTACK ON 24th APRIL 2004 
         There were two rounds 1)TECH(30 ques,30 mins)2)APTITUDE(30 ques,30 mins)

         TECH QUESTIONS (Electronics & TC)

CMRR is given=
Differential gain is given=  
Inputs:
+ve end=2v,-ve end=1v of the OP-AMP                                                            
Find the output voltage?

CRO is in X-Y mode.Sinusoidal inputs have 90degrees phase difference between them. What will appear on the display? a)circle b)line c)ellipse d)triangular wave

Which has least propagation delay?
   a)ECL b)TTL c)RTL d)CMOS

In a ripple counter how many change in states happen when count changes from7 to 8?
a)1 b)2 c)3 d)4

Max. no. of variables that can be represented in K-MAP?
    a)3 b)5 c)7 d)none of these

How many comparators are required in a n-bit flash ADC?
   a)2^(n-1) b)(2^n)-1 c)2^n d) n

What is an EEPROM?
   a)Programmable transistor
   b)Transistor
   c)SRAM
   d)

Time period of input voltage=8ns. / Find the duty cycle of Vout.                                          
  
Voltage across one capacitor is V volts. Another cacitor is added at its one end(now the two are in series). What is the voltage across their ends?
 a)V b)V/2 c)2v d)none of these
 In an SCR why silicon is used?
     a)  available easily
     b)  has much less reverse saturation current than Germanium
     c)  has greater reverse sat.current than Ge
     d)

Output=?
   

     a)A+B+C
     b)A+B+C
    c)A(B+C)
    d)B+C+A
There was a question using transmission gates.Three inputs were A,B,C.Answer was  (A+BxorC)
How to get the characteristic figure changed from 1 to 3?(characteristic diagram)
  
            a)By increasing gate width of NMOS
            b)---------do----------------- of CMOS
            c)By increasing gate voltage

 Find propagation delay?
                                    
    a)200Hz b)150Hz c)5Hz d)2Hz
A diagram was given to identify?
   a)Synchronous counter
   b)Ripple counter
   c)Shift register
   d)None of the above
     answer was sync. Counter

Find Va?and Ia, Ib?
    
Find ammeter current Ia?
                                    
       a)10V  b)9.09V c)11.01V  d)0.9V    these options may be wrong.
          
   This acts as a:
   a)OR
   b)XOR
   c)AND
   d)NOR

At t=0 if position is changed from 1 to 2 ,find the voltage across 1KΩ?
    
   a)4V b)2V c)1.5V d)none of these

Find thevenin voltage and resistance across A and B
  

how will be the output voltage across R ?
 
       

               
    Ans C

What is this ?
   

a)Integrator b)Differentiator c)Antilog differentiator d)Log differentiator

 

  Flip-flop state diagram question.What does the above represent?                                   

What is this?
  

   a)Squaring device b)Divider c)Square root ckt d)

How will be the output vs. input graph if Vin=10V,sat voltage of OP-amp is 14V?
 

 

Basic memory cell of dynamic RAM a. Capacitance
b. Flip flop
c. Transistor
d. Transistor with Capacitor

 Ideal Power Supply has
a. Zero internal resistance
b. High O/P resistance
c. High I/P resistance Freshersworld.com                                                             
d. Low O/P resistance

Which type of transmission line will have max. value of characteristic impedence a. Open Wire line b. Coaxial Cable
c. Twin lead line    d. None

 For same peak value of current, which waveform will have least RMS value a. Sine b. Square
c. Triangular
d. Full wave rectified wave

-V analogy displacement is analogous to
a. Voltage b. Condutance
c. Magnetic Flux Linkage
d. Capacitance
Similarly..............In F-I analogy displacement is analogous to
a. Charge
b. Resistance Freshersworld.com
c. Inductance
d. Current

In the following circuit Vo/Vin = (there were 4 options)
    

In the following circuit the charging and discharging time is  (i dont remember the options)
   
   Don,t remember the other value of other res and cap .But some values are given             

The output at X acts as.
  
           a.OR gate
          b.AND gate
          c.XOR gate
        d.XNOR gate

The CRO in X-Y mode gives the following figure. If signal applied to the Y-plate is 2sin(wt) then the signal  applied to the X  is    a. 2 sin (wt) b. 2 sin (wt + p/4) c. 2 sin (wt d.22 sin (wt + p/4)